Palmer Standard Stabilizer Regulator

All of the features and performance of our legendary "ROCK" regulator, but designed and built for the high pressure output needed to regulate and stabilize pressure controlled paintgun velocity. Well suited for use as the first stage of a 2- stage regulation system for the AutoMags or in the role of the second stage of an on-gun or remote system for all paintguns; with either CO2, Compressed Air, Nitrous Oxide, N2 (nitrogen), HPA pressure supply systems. Two stage regulation will provide approximately 25 times greater control and consistency of the supply pressure that is allowed into the paintgun. Expansion chambers can't even hope to block liquid CO2 the way the that the Stabilizer can, thus virtually eliminating the chance of "hot-gun" penalties. The long proven performance of Palmer's Regulators, makes the "STABILIZER" a must for all pressure controlled firing systems for any paintgun. Available in five different models to cover numerous applications and setups .  Industrial, NASA, scientific, medical and custom applications available. Works in any position, upside down or even in zero gravity.  Shock proof.

Fully adjustable; 0-800 psi output

  Omni-Gas Ready   (HPA or CO2)

Most paintball applications only need the standard Stabilizer.  It's adjustable from 0-800 psi with max input of 1800 psi. The standard Stabilizer  will work with Co2 and HPA without any changes. A 3/16 allen wrench is used to adjust pressure. No tourney locks required. The Stabilizer is shipped with a factory test setting of 500 psi. Just unscrew the adjuster before install for lower pressures. One turn of the screw is about 100 psi average.

Where I want to mount a reg?

Vertical Mount [Male , Fatty, Direct]
Bottom Line Mount [Female]
Remote/Hard-line Mount [Inline, Female]

What Regulator Should I get? Required Pressure range?

Standard Male Stabilizer. Our most versatile regulator that gives a wider pressure range Accepts low pressure kits if lower pressure range is desired. Perfect for high pressure blow backs like Tippmanns and Spyders.

Fatty, Our best low pressure reg made for most low pressure paintball guns. The Fatty also has better consistency than the standard Stabilizer. Spring maxes out at 425 psi. Only comes in vertical configuration. Great for the Matrix, Impulse Intimidator, AKA, Autocockers, and any other gun that works under 400 psi. 0-800 psi 0-400 psi 0-250 psi

Stabilizer with a low pressure kit, Used for very low pressures, non-paintball uses, or wherever else the Fatty wont fit. Spring maxes out at 300 psi. The Male, Female, Direct, and Inline accept the low pressure kit.

Types of Regulators:

In Line

1/8 NPT 27 threads ..   Same size as stainless mesh hose Output is on the side... Input on the top  ...opposite of  the Direct Stabilizer

Side Line

Quick disconnect nipple..    For use with Automags Output is on the side... Input on the end  ...opposite of  the Direct Stabilizer

FEMALE Stabilizer

Female bottle threads on the intput end for direct connection to a bottle. Most commonly used in the bottom line position. Gauge can be installed to read regulated pressure upon request.

MALE (a.k.a. Vertical)

Male bottle threads on the output end for direct input to standard ASA. Most commonly used in the vertical position. Gauge can be installed to read regulated pressure. Output is on the top... Input on the side

Direct 

1/8 NPT 27 threads ..   Same size as stainless mesh hose Output is on the top... Input on the side...opposite of  the Inline Stabilizer Will not fit Tippmann 98

- built for any marker that was built without an ASA on the front. Spyders without ASA or expansion chamber, Mini cockers,  Impulse, ect.... Gauge can be installed to read regulated pressure.

Fits on these models plus many more ( let us know what it fits and we will add it to the list)

Spyder Aggressor XT Tippmann Procarbine

Input on the side, output on the other side and top